Samsung - vracanje tvornickih postavki

jel zna neko mozda kod za vracanje tvornickih postavki za samsunga

00000000 ( 8 nula )

btw znam još za nokiu => 12345 i motorolu => 000000 ( 6 nula)
Trenutno te mobove imam, za ostalo ne znam...

Imam rotaciju plavu na ekranu , kako da ju maknem , i ne nije slika , stoji u alatnoj traci

plava rotacija !? izgleda li kao ona kod uspostave poziva ?

pa neznam nisam nikad vidio kak izgleda kod uspostave poziva al vjerojatno nije uglavnom izgleda ko policijska rotacija

Koji model imaš? Jesi probao izvaditi bateriju, vratio na tvorničke postavke, poništio (za svaki slučaj) preusmjeravanje poziva?! Pročačkaj malo cafe mobile frorum..koliko me pamćenje služi, naletila sam tamo prije god dana na razne kodove..a i regaj se pa napiši problem, uvijek netko odgovori.. U najgorem slučaju odi kod onih dečkiju u Radićevoj, G zona,odmah kraj vipa..

Nedavno sam dobila na poklon Samsung D500, primjetila sam da se videi i slike mogu zaključati, ali je potreban nekakv pin kojeg ja naravno nemam, zna li neko možda da li postoji tvornički pin ili sl. što treba ukucati?

Evo zgodnih podataka za Samsung ( from www.recenzije.hr )

Kodovi za Samsung mobilne telefone
*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0001# -> Show Serial Parameters

*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!!!! but also
change IMEI to 447967-89-400044-0, you must use CHGIMEI to
restore it)
*2767*2878# -> Custom EEEPROM Reset

*#9998*228# -> Battery status (capacity, voltage, temperature)
*#9998*246# -> Program status
*#9998*289# -> Change Alarm Buzzer Frequency
*#9998*324# -> Debug screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error Stack
*#9998*427# -> Trace Watchdog
*#9998*523# -> Change LCD contrast
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service Table
*#9998*785# -> RTK (Run Time Kernel) errors
*#9998*786# -> Run, Last UP, Last DOWN
*#9998*837# -> Software Version
*#9998*842# -> Test Vibrator
*#9998*862# -> Vocoder Reg
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal Error
*#9998*999# -> Last/Chk

*#9998*9266# -> Yann debug screen (=Debug Screens?)
*#9998*9999# -> Software version

*0001*s*f*t# -> Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# -> unknown
*0003*?# -> unknown



Samsung SGH-600, 2100, 2200, 2400
To display IMEI type *06#

1. Software Version : *#9999# and *#0837#
(instructions)
2. Serial Port Info : *#0001#
3. Batt./Temp. Meter : *#0228#
4. Sim Card Info : *#0778#
5. SIM capacity display: *#0746#
6. Memory error : *#0377# Use side keys to
select values. Cancel and ok.
7. Error Message : *#0785#. If ok is pressed
the phone will reset and
register this on the memory error.
8. Alarm Tone Adjust : *#0289#
9. Date/Time Log : *#0786# Last up and down.
10. Memory Info : *#0246#
11. LCD Contrast : *#0523# Only with version
G60RL01W.
12. Network Monitor : *#0324#
13. Memory Usage : *#0636#
14. Trace Watcdog : *#0427#
15. Buzzer adjust : *#0289#
16. Phone Parameter : *#0862# Normal, Earphone or
carkit can be
selected.
17. Activate light & Vibra : *#7698# Flash the
screenligth during 10 seconds,
the activation of vibration system.
18. Activate smiley. : *#9125# Activates the
smiley when charging.


Unidentified Code:

*#0872# Diag? Parameter can be changed with sidekeys.
*#0544#: Jig detect ?
*#0364# Watchdog ?

NB! Since version G60RL23M , it seem that only *#06# , *#0001#
e *#9999#, works.

Pin-Out 1- GND 2- RS232 TXD 3- RS232 RXD 4- RS232 RTS 5- MAX 4.2 IN Š? 6- GND 7- GND 8- SPK - OUT 9- SPK + OUT 10- SCL I2C comm proprietary bus 11- SDA I2C comm proprietary bus 12- RS232 CTS 13- VCC 5V OUT 14- DC 9V IN 15- DC 9V IN 16- MIC + IN 17- MIC - IN 18- +3.6V IN battery 19- GND 20- Antenna 21- Antenna 22- GND 23- GND 24- n.c. 25- Temperature sensor IN 26- +3.6V IN battery 27- GND 28- GND


SP-unlock SGH-600

*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! )
*2767*2878# -> Custom EEPROM Reset

These codes has been tested with version FLD_2C6 G60SB03X of Samsung SGH-600

Samsung SGH-600 / SGH-2100 Mobile Home

*#9998*228# -> Battery status (capacity, voltage, temperature)
*#9998*246# -> Program status
*#9998*289# -> Change Alarm Buzzer Frequency
*#9998*324# -> Debug screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error Stack - Use side keys to select values. Cancel and ok.
*#9998*427# -> Trace Watchdog
*#9998*523# -> Change LCD contrast - Only with version G60RL01W
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service Table
*#9998*785# -> RTK (Run Time Kernel) errors - if ok then phn is reset, info is put in memory error. *#9998*786# -> Run, Last UP, Last DOWN
*#9998*837# -> Software Version
*#9998*842# -> Test Vibrator - Flash the screenligth during 10 seconds and vibration activated.
*#9998*862# -> Vocoder Reg - Normal, Earphone or carkit can be selected
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal Error
*#9998*999# -> Last/Chk

*#9998*9266# -> Yann debug screen (=Debug Screens?)
*#9998*9999# -> Software version

If the up Codes doesn't work, you should change *#9998* to *#0. i.e. *#9998*523# change to *#0523#. An other thing that will help is to remove your simcard.

*0001*s*f*t# -> Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# -> unknown
*0003*?# -> unknown

SP-unlock SGH-600 and SGH 2100

*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! )
But also changes IMEI to 447967-89-400044-0, To restore your old IMEI use the IMEI program found on the software page.

*2767*2878# -> Custom EEEPROM Reset

Ja sam ukucao 00000000 ( 8 nula ) i javlja mi ne tocna sifra! Jedno pitanje htio bih u svoj samsung ubaciti nove igrice,teme idr sa koji koblom da to napravim?! Hvala

nevidim je napisao/la: › jel zna neko mozda kod za vracanje tvornickih postavki za samsunga

x2767x3855# samo ukucaj dalje radi sam

Pročačkaj malo cafe mobile frorum..koliko me pamćenje služi, naletila sam tamo prije god dana na razne kodove..a i regaj se pa napiši problem, uvijek netko odgovori.